If you have ever stood near a window on a cold Melbourne morning and felt a chill despite the heating being on, your single glazing is likely the cause. Single glazed windows are the standard fitout for most Australian homes built before the 2000s, but they are also one of the biggest sources of heat loss in any home.
Double glazing changes that fundamentally. This guide breaks down exactly how single and double glazing compare, what the difference means for your comfort, your energy bills and your home, and whether upgrading to double glazed windows is worth it for Melbourne conditions.
How single glazing works (and why it falls short)
A single glazed window is, as the name suggests, a single pane of glass set into a frame. That glass is typically 3mm to 6mm thick. Glass conducts heat readily, which means that in winter, warmth from inside your home is drawn straight through the pane and lost to the outside. In summer, solar heat passes through in the opposite direction, driving up indoor temperatures and putting more load on air conditioning.
The practical result is a window that acts more like a radiator than an insulator. Single glazed windows can account for up to 40% of a home's total heat loss in winter, according to the Australian Greenhouse Office. For homes with large window areas, particularly those with heritage timber frames or floor-to-ceiling glass, the impact is even more pronounced.
Single glazing also provides almost no acoustic benefit. Traffic noise, aircraft, neighbours and street activity pass through largely unimpeded. And condensation forms readily on the cold inner surface of single pane glass during winter, which over time can damage timber frames, paint and furnishings.
How double glazing works
Double glazing uses two panes of glass separated by a gap, typically filled with argon gas, to create a thermal barrier. Heat must travel across the first pane, through the insulating gas gap and across the second pane before it can escape. That gap is the key: argon gas is a poor conductor of heat, so the rate of heat transfer drops significantly compared to a single pane.
Modern high-performance double glazing also incorporates a Low-Emissivity (Low-E) coating on the inner pane. This microscopically thin coating reflects radiant heat back into the room in winter, while blocking solar heat gain in summer. The result is a window that actively works with your heating and cooling system rather than against it.
Single vs double glazing: a direct comparison
| Feature | Single Glazing | Double Glazing |
|---|---|---|
| Thermal insulation | Poor. High heat loss in winter, high heat gain in summer. | Excellent. Argon gas gap and Low-E coating dramatically reduce heat transfer. |
| U-value (typical) | 5.0 to 6.0 | 0.4 to 2.5 depending on glass type |
| Energy bills | Higher heating and cooling costs year-round. | Up to 60% reduction in energy usage. |
| Noise reduction | Minimal. Street noise, traffic and aircraft pass through easily. | Significant. Acoustic variants rated Rw38 reduce noise by up to 50%. |
| Condensation | Common in winter. Can damage frames and furnishings. | Greatly reduced. Inner pane stays closer to room temperature. |
| Home comfort | Cold near windows in winter, hot in summer. | More even temperature distribution throughout the home. |
| UV protection | Minimal. Furnishings and flooring fade over time. | Acoustic variants block over 99% of UV transmission. |
| Security | Single pane breaks easily under impact. | Grade A toughened safety glass as standard. Laminated variants add further resistance. |
| Property value | Neutral | Recognised as a desirable upgrade in the Melbourne market. |
| Environmental impact | Higher ongoing emissions from energy use | Lower energy use. Retrofit approach preserves existing frames, reducing waste. |
Does double glazing make sense in Melbourne?
There is a persistent misconception that double glazing is only worthwhile in extremely cold climates. Melbourne's winters are mild by European standards, so does the investment pay off here?
The answer is yes, for several reasons specific to Melbourne's climate and housing stock.
Melbourne experiences a wide temperature swing across the year, from well below 10°C on cold winter nights to 40°C+ during summer heatwaves. That range puts significant demand on both heating and cooling systems. A window that leaks heat in winter is the same window that lets summer heat pour in, so the energy saving applies year-round.
Melbourne is also home to a large proportion of older housing, with Victorian, Edwardian and mid-century homes common across the inner suburbs and many regional areas. These homes almost universally have single glazed timber windows, which are both the weakest thermal point in the building and often too heritage-significant to replace outright. Retrofit double glazing addresses both issues directly: the glass is upgraded without touching the original timber frames.
Heritage homes and double glazing: For homes in heritage overlays or those with original timber windows, full window replacement is often not an option. Retrofit double glazing inserts a new double glazed unit directly into the existing frame, preserving the character of the home while delivering modern thermal and acoustic performance.
The three performance levels of double glazing
Not all double glazing is the same. RetroFit Double Glaze offers three glass types at different performance levels, allowing homeowners to match the glass to their priorities and budget.
LightBridgeâ„¢ / Optithermâ„¢
The standard and most popular option. Low-E coated toughened glass with an argon gas gap, delivering a U-value of 1.4 and up to 75% less heat loss than single glazing. The right choice for most Melbourne homes.
LightBridge Nextâ„¢ / Optitherm Hushâ„¢
All the thermal performance of the standard unit, with the addition of an acoustic laminated outer pane rated Rw38. Best for homes near busy roads, train lines, trams or flight paths. UV transmission is reduced to under 1%, protecting furnishings from fading.
Vacuum Insulated Glass (VIG)
The highest-performing option available. A 0.3mm vacuum gap replaces the argon gas fill, delivering a U-value of 0.4 and up to 93% less heat loss, in a total unit thickness of just 8.3mm. Ideal for heritage windows where a standard IGU would not fit the existing rebate.
Single glazing: is there any case for keeping it?
In most circumstances, no. The energy savings, comfort improvements and noise reduction that double glazing delivers make it a worthwhile upgrade for the majority of Melbourne homes. The main reason homeowners retain single glazing is cost, but when weighed against the ongoing savings on energy bills and the improvement to daily liveability, the payback period is generally favourable.
There are some situations where single glazing may be retained in the short term: a home due for significant renovation, a rental property where the landlord's timeline does not align with an upgrade, or a window type that falls outside the current scope of retrofit glazing (such as steel or aluminium frames). In those cases, heavy curtains or external shutters can provide some interim benefit.
| Double glazing: key benefits | Single glazing: limitations |
|---|---|
| Up to 75% less heat loss | High heat loss in winter |
| Up to 60% reduction in energy bills | High heat gain in summer |
| Significantly reduced noise | Higher ongoing energy costs |
| Reduced condensation on windows | Minimal noise reduction |
| More consistent indoor temperatures | Condensation and moisture damage |
| UV protection for furnishings | No UV protection |
| Improved home security | Easier to break under impact |
| Suitable for heritage timber frames | Cold draughts near windows |
| Adds property value |
What does double glazing cost compared to single glazing?
Single glazing costs less upfront as an installation, but that comparison misses the ongoing cost of running a thermally inefficient home. Heating and cooling a home with single glazed windows costs more year after year. Double glazing is an investment that reduces those costs over time.
For homeowners considering full window replacement as an alternative to retrofit double glazing, the cost difference is significant. Full replacement of timber windows, including new frames, typically costs three to five times more than retrofitting the existing frames with new double glazed units. The retrofit approach also avoids the disruption, plastering and repainting that frame replacement requires.
Retrofit vs replacement: Full window replacement in a Melbourne home typically costs $30,000 to $60,000 or more. Retrofit double glazing achieves comparable thermal and acoustic performance at a fraction of that cost, by keeping your existing frames and upgrading only the glass.
The verdict
Double glazing outperforms single glazing in every meaningful category: thermal insulation, noise reduction, energy efficiency, comfort, security and UV protection. For Melbourne homeowners, particularly those in older homes with original timber windows, retrofit double glazing offers a practical path to modern performance without the cost or disruption of full window replacement.
RetroFit Double Glaze has been upgrading Melbourne homes since 2011, with a 4.9-star rating across 110 Google reviews. We work exclusively with Glassworks and Viridian Glass to supply three glass types at different performance levels, with options for thermal performance, acoustic insulation and heritage window profiles.
To find out which glass type suits your home, get in touch for a free measure and quote.




